How to get CMC controllers in DEMO mode

This section is about Steinberg's CMC controllers
Post Reply
User avatar
istokblues
Junior Member
Posts: 63
Joined: Sat Jul 16, 2011 9:30 am
Contact:

How to get CMC controllers in DEMO mode

Post by istokblues » Sun Feb 26, 2012 7:00 pm

Somebudy know how to put the controllers in DEMO mode ( flashing lights ) ????
istok

Stefan Schreiber
Moderator
Posts: 201
Joined: Tue Dec 14, 2010 10:49 am
Contact:

Re: How to get CMC controllers in DEMO mode

Post by Stefan Schreiber » Tue Feb 28, 2012 9:24 am

Hi istokblues,

To activate the demo mode (Las Vegas mode) on the CMC units please take the following steps:

To activate the "demo mode select state", plug in the USB cable while press-and-holding a combination of two buttons described in the attachment of this post. The CMC unit stays in "demo mode selecte state" for 10 seconds when powered by the plugged USB cable.
Now set the controller to demo mode by pressing the according button, as decribed in the attachment.
The demo mode status is saved and remains so until being disabled by following the same procedure and pressing the according button.

Example:
CMC-CH
1. Press and hold SHIFT and MONITOR button
2. Connect USB cable
3. Release SHIFT and MONITOR button
4. Press MUTE button once
5. You will see the fader LEDs going up/down a few times
6. Wait for a while and you will see the LEDs light up randomly
CMC demo mode.jpg
(295.4 KiB) Not downloaded yet
This feature is not officially supported and might be removed without notice in the future.

Enjoy the show ;-).

Best regards,
Stefan Schreiber
Stefan Schreiber - Senior Marketing Manager Hardware
Steinberg Media Technologies GmbH
Hamburg, Germany

Connect with Steinberg on Facebook, YouTube, Twitter, Instagram, SoundCloud

User avatar
istokblues
Junior Member
Posts: 63
Joined: Sat Jul 16, 2011 9:30 am
Contact:

Re: How to get CMC controllers in DEMO mode

Post by istokblues » Tue Feb 28, 2012 6:39 pm

Thank you Stefan !!! Nice ! I like it very much !!!
istok

User avatar
Rommelaar
Member
Posts: 284
Joined: Sat Jan 11, 2014 4:09 pm
Contact:

Re: How to get CMC controllers in DEMO mode

Post by Rommelaar » Wed Aug 06, 2014 9:26 am

I just tried this with all the CMC controllers I have over here. Really nice, as soon as you use a controller they behave normally. Las Vegas mode returns after a while when you haven't used them for a short time. After a power shut down of the USB-hub, the controllers are still in Las Vegas mode.

I had to turn Las Vegas mode off, since it was too much of a distraction while working with Cubase. You have to manually turn each controller off as described in the picture.
Rig: i7-5960X, Asus X99 Deluxe, Corsair LPX DDR4 64 GB RAM, Samsung 34" C34F791, Asus Strix GTX 970, Windows 10 Pro 64-bit
Audio hardware:KRK Rokit 6, Steinberg UR44 / CMC: AI, 4xFD, CH, QC, TP, PD, Waldorf Blofeld & Pulse 2, ZOOM H6, Akai MAX49, Akai MPD226
Software: Cubase Pro 10.0.40, Nuendo 10.2, Wavelab Pro 10 , Dorico 3, Spectralayers, RapidComposer v3.81
Favourite plugin developers: Fabfilter, Image Line, Spectrasonics, Steinberg, Synapse audio, Vengeance sound, Waldorf, Zynaptiq

Post Reply

Return to “Steinberg CMC Series”

Who is online

Users browsing this forum: No registered users and 1 guest