Steinberg Ci1 setup

This section is about Steinberg's USB audio interfaces CI1, CI2 and CI2+
Post Reply
MLarzen
New Member
Posts: 1
Joined: Fri Feb 25, 2011 6:19 pm
Contact:

Steinberg Ci1 setup

Post by MLarzen » Fri Feb 25, 2011 6:23 pm

Hi!
I just bought my steinberg Ci1 usb-interface but can't find where i should set it up so i can hear the sound from Cubase on my ESI nEar 05 monitors.

Every little bit of knowledge could help!

User avatar
JHP
Member
Posts: 755
Joined: Wed Nov 03, 2010 1:58 pm
Contact:

Re: Steinberg Ci1 setup

Post by JHP » Tue Mar 01, 2011 4:45 pm

The first things you must do when you connect your Ci interface and startup Cubase:

1. ASIO driver in VST Audiosystem
In Cubase go to "Devices--> Device Setup--> VST Audiosystem" and select the ASIO driver for your Ci interface, Yamaha Steinberg USB ASIO.

2. VST Connections
The VST Connections are very important!
After you have set up the ASIO driver you must set up the "VST Connections" under "Devices--> VST Connections".

:arrow: The "VST Connections" are to connect the virtual buses in Cubase with the physical hardware inputs and outputs of your hardware device.

Setting up the Cubase Output
To get started the "Output" tab in the VST Connections is the most important because only if you set this up correctly you will be able to hear the Cubase output.

Click on "File--> Import--> Audio File" and import an Audio File.
After you have imported an Audio File hit "Play" and check if you can hear the playback.
Open "Devices--> VST Connections" and click on the Output tab. Now assign the virtual "Stereo Out" with the physical output of your Ci interface by clicking next to it in the device port column. In most cases the device port is already be assigned correctly.

Simplified this is how the Signal flows when it comes to playing back audio on an audio track:

Audio Track in Cubase (flows to) --> "Stereo Out" Masterfader in Cubase (flows to) --> Physical Outputs of your Ci interface that you have connected with the virtual "stereo out" in the VST Connections (flows to)--> the speakers or headphones that you have connected to the physical outputs of your Ci interface.

Setting up the Cubase Inputs for recording
Connect Mic/Guitar to physical input of your Ci interface.
Open "Device--> VST Connections" and click on the input tab.
Click on the input tab and create a virtual Mono Bus "Mono In".
Now you must connect the virtual "Mono Bus" with the physical Input of your Ci interface by clicking next to it in the "Device Port" column.
Create a new empty audio track "project--> Add Track--> Audio --> Mono".
Make sure that you have the virtual input bus connected to that track. For the track it should say "Mono In" as Input and "Stereo Out" as output. If everything is setup correctly you should be able to record if you record enable the track and press record on the transport bar.

Simplified this is how the Signal flows when it comes to recording:
From Mic/Guitar to physical Mono input of Ci interface flows to--> virtual Mono Bus flows to --> Audio Track that has the virtual "Mono Bus" defined as Input in the inspector--> write to disk.

Gr,
JHP
Jan Peters, QA
Steinberg Media Technologies GmbH
Hamburg, Germany
Check out Steinberg on YouTube, Twitter and Facebook!

Nat
New Member
Posts: 1
Joined: Fri Sep 23, 2011 12:47 pm
Contact:

Re: Steinberg Ci1 setup

Post by Nat » Sun Oct 16, 2011 5:21 am

What kind of head phones do I need to buy to use with my USB Audio Interface CI1?

Cheers

Nat

User avatar
Bane
Senior Member
Posts: 1728
Joined: Sun Jul 10, 2011 2:57 am
Contact:

Re: Steinberg Ci1 setup

Post by Bane » Wed Oct 19, 2011 1:14 am

You could use normal headphones (like you'd plug into your ipod) and connect those to your Ci1 through a 3.5 mm 1/4 inch female to 1/4 inch male stereo adapter. That would be the cheapest way.
Asus R500A-RS52, Windows 8, 2.6gHz i5 -3230M, 6GB RAM,

Cubase Artist 7.0.6, Wavelab Elements 7, Focusrite Scarlett 8i6, The Grand 3, Melodyne Essential, Superior Drummer, EZDrummer and Pop! EZX, Samson CO1, Yamaha P-35, Mackie MR5mk2 monitors, and more....

My tunes on: Soundcloud

User avatar
Bane
Senior Member
Posts: 1728
Joined: Sun Jul 10, 2011 2:57 am
Contact:

Re: Steinberg Ci1 setup

Post by Bane » Wed Oct 19, 2011 11:27 pm

In fact, I just purchased an adapter today, because I was apparently using a mono one and thus sound would only come out of one side. They are really cheap, most places will sell you one for $2-3. So, I am using a Hosa 3.5 mm TRS to 1/4 inch TRS stereo headphone adapter with my Ci1, and it sounds much better than the mono! ;)
Asus R500A-RS52, Windows 8, 2.6gHz i5 -3230M, 6GB RAM,

Cubase Artist 7.0.6, Wavelab Elements 7, Focusrite Scarlett 8i6, The Grand 3, Melodyne Essential, Superior Drummer, EZDrummer and Pop! EZX, Samson CO1, Yamaha P-35, Mackie MR5mk2 monitors, and more....

My tunes on: Soundcloud

Post Reply

Return to “Steinberg CI Series”

Who is online

Users browsing this forum: No registered users and 0 guests